OUR PRODUCTS

Mechanical Pullar Hpuller

MODULAR, SLIDING DESIGN PULLERS 'PULLRIGH'

An attempt should always be made to dismount any machine element including bearings, pulleys, couplings and gears without damaging them, especially where the intention is to remount them.

Most of the pullers available today have serious limitations since the jaws slip, tip of jaws bend/break, threads of spindle gets damaged. PULL RIGHT EXTRACTORS overcome all these limitations of conventional pullers.


The major advantages of these pullers are :

(1) The two/three jaws slide backward/forward on precision ground Tee section. The jaws are coplanar over the entire width thus ensuring FULL GRIP over the machine element requiring extraction.

(2) There is a facility of locking puller jaws to avoid any SLIPPAGE while extracting machine elements like bearings, pulleys, couplings etc.

(3) All parts are made from high-grade alloy steel, toughened to 25-30Rc and precision ground to maintain parallelism of jaws. Spindle is of EN 24 and Nitrided. This ensures high LOAD CARRYING CAPACITY and also gives long life to the puller.

(4) There is a rotating center to reduce damage to shaft. A specially designed Tommy is provided to apply extra torque required to remove jammed pulleys/couplings. A gunmetal ring has also been provided to eliminate damage to spindle.

HEAVY DUTY, LONG LASTING, HIGH PERFORMANCE PULLERS FOR BEARINGS, PULLEYS, GEARS AND COUPLINGS.

MODEL SELECTION CHART

It is advisable to select minimum two models, one in the range of 150/200 mm and other in the range 300/450 mm spread

Table I Two Jaw Extractors
MODEL MIN. DIA
mm
SPREAD
mm
REACH
mm
WITHDRWAL
LOAD kg.
P01 20 100 130 1500
P02, P03, P04 30 150 200, 250, 300 5000
P05, P06, P07 30 200 200, 250, 300 5000
P08, P09, P10 50 250 200, 250, 300 8000
P11, P12, P13 50 300 200, 250, 300 10000
P14, P15, P16 50 300 200, 250, 300 10000
Table I Two Jaw Extractors
MODEL MIN. DIA
mm
SPREAD
mm
REACH
mm
WITHDRWAL
LOAD kg.
P20 030 120 150, 150 3000
P21, P22, P23 050 150 200, 250, 300 7500
P24, P25, P26 050 200 200, 250, 300 10000
P27, P28, P29 070 250 200, 250, 300 12000
P30, P31, P32 080 300 200, 250, 300 15000
P33, P34, P35 100 450 200, 250, 300 20000

Eg.-1 P02 Max. Reach =200mm, P03 Max. Reach =250 mm, P04 Max. Reach = 300 mm whereas spread in all three models remains 150 mm

ACCESSORIES

1) CHISEL JAWS :

Many a times there is not enough space behind bearing, gears etc. to accommodate jaws of existing pullers. We offer chisel type jaws which are fully interchangable with standard jaws. These Chisel jaws are common for all models except P01, P20. Chisel jaws are not required for model P01 & P20. Two jaw pullers would require 02 chisel jaws, whereas three jaw pullers would require 03 chisel jaws. Load carrying capacity of these chisel jaws would be 50% of standard jaws.

2) EXTRA HOLDERS :

In many applications reach of standard puller is insufficient since distance between edge of shaft and bearing etc. is large. We can offer extra holders to extend reach. (two holders for 02 jaw puller and three holders for 03 jaw puller). Along with extra holders a rotating distance piece is given to extend length of spindle. These extra holders are available for 100mm, 150mm & 200mm length. We can thus get a maximum reach of 500mm.

3) JAWS FOR MOTOR FANS :

These are specially made to dismount fans of motors. Normally motor fans have two slots. These slots can be square, round or triangular. The tip of the jaw can accommodate slot size of 8mmx8mm. These fan jaws are totally interchangeable with standard jaws. These jaws have low load carrying capacity and should only be used for removing motor fans. These fan jaws are suitable for only two jaw pullers since motor fans have only 02 slots. Fan jaws are separate for P01 & common for all other two jaw models.

4) 'C' WASHERS :

While extracting bearings with bore of 50mm and above there is a possibility of damaging the bearing since load is applied on outer ring. A practical solution is to insert a 'C' washer behind the bearing and put jaws of puller over it. These 'C' washers are made from alloy steel, hardened , ground and individually numbered according to bearing size for identification. Hence please specify bearings you wish to cover. e.g.-1. For bearing 6313, 'C' Washer is designated as 65-140. e.g.-2. For bearing 6319, `C' Washer is designated as 95-200. The first digit is bearing I.D, the second digit is bearing O.D.

Dismounting

TO DISMOUNT ANY M/C ELEMENT YOU NEED A MECHANICAL / HYDRAULIC PULLER

When you use a Puller ONLY TWO THINGS HAPPEN

(a) The element i.e. bearings, couplings, pulleys, gear gets dismounted.
(b) The puller gets DAMAGED/SLIPS Ref. Fig.2